4 layer kappa hardboard production machine

 

The cardboard composite production line is suitable for 2-4 layers of 70-600 g/m2 reel grey paper,through the hydraulic support, bridge transmission, edge, preheating, glue, bonding, shaping, traction, cutting, crosscutting and receiving table and other processes composite for the required various thickness and specifications of thick cardboard.The production line has reasonable design, compact structure, high degree of automation, convenient operation and maintenance, energy saving and many other characteristics.Make up for the many shortcomings of the single machine manual pasting.Greatly reduce the production cost, improve the quality of products,The flatness, stiffness, surface finish and bonding strength of cardboard are greatly improved,It is the ideal equipment for making cardboard.

 

RX-D 1600 4 Ply Cardboard Composite Production Line-Steam Heat
           Design Speed: 120 m/min, Economic Speed: 60-100 m/min
1.

Lum-D

 Hydraulic shaftless mill roll stand 4set 1. Hydraulic drive and multi-point brake can complete lifting, clamping and loosening of base paper.
2. Move centering, adopt pneumatic tensioner to adjust the tension of base paper,
3. Clamp paper diameter 1500, taper cast iron top; (with automatic tension).
4. There is a set of guide rails for each mill roll stand, and the paper loading trolley is welded with 10mm thick medium plate5. 1
 

2.

Lum-D

 Over transport bridge

 

 1set Heavy duty bridge and stainless steel guardrail

 

3.

Lum-D

 4 ply Side-correcting machine

 

 1set  

1Taiwan Gold ultrasonic automatic edge alignment system, flexible movement;

 
4.

Lum-D

 Four layer pre-heater

 

 1set 1.Main drive roller:Φ600mm,electric adjust wrap corner, 2.Paper wrap angle adjust scope 360 degrees;

600mm;

Corner  wrap  available at  360

Adjust the paper heating area within the range;

 
5.

Lum-D

 Quartic gluing machine

 

 1set 1.Glue roller diameter 270mm,with 25 line reticulate pattern, 2.The diameter of uniform gluing roller is 215mm, the surface of the roller is hung with hard glue, and the glue is uniform 3.Pressing roller Dia is 110mm.Pneumatic control lift and down. 4.electric adjust glue gap

5.Independent variable frequency motor drive; 6.Motor power of each layer: 3.0KW speed ratio 1:9
 

6.

Lum-D

  

Bonding compaction machine

 

  

1set

 1.     Including 2 multi – head spiral folding paper roller

2.     Pneumatic lift, 4 groups of compaction roll φ 240mm 1. 2 2.，4 Φ240mm
7.

Lum-D

 Traction machine

 

 1set 1.     Traction roller Φ525mm,upper roller Φ525mm

2.     Excelsior grinding hard chrome plating, independent drive; Frequency conversion control.

3.     Motor power 11KW speed ratio 1:23

 
8.

Lum-D

 Steam heating baker

 

 1set 1.26 sets of finned coil heater, the lower layer is sealed with thermal insulation cotton

2.  Upper side open movable cover seal, stainless steel insulation box

3.  16 sets of conveying roller, diameter 105mm

4.        Pneumatic    regulation,    independent   drive,       frequency conversion control, power 15KW

 

 

9.

Lum-D

 Shaping                    compactor machine

 

 1set 1.21 sets of compaction roller, diameter 105mm, pneumatic lift 2.Install 15 fan for cooling and shaping

 
10.

Lum-D

 Traction slitting machine

 

 1set 1. The lower roller diameter of the tractor is 525mm, hard chrome plating;

2. The diameter of the upper roller is 420mm, covering the glue grinding;

3.     Frequency conversion control, power 18.5KW;Speed ratio 1:23

4. Electric adjustment, largediametertrimmingknife

 
11.

Lum-D

 NC cut off machine (Helical knife)

 

 1set 1.Servo computer control, automatic order change 2.Cutting paper range 400-9999mm

3.Knife shaft diameter 198mm, power 22KW

 
12.

Lum-D

 Drum type plate turning machine

 

 1set 1. Fully automatic drum-type turning plate

2. Automatic positive and negative unfold paper insertion function

3. Manual control of cardboard waste discharging and sampling inspection

 
13.

Lum-D

 Electric system

 

 1set 1. Electronic control system: variable frequency motor   control full line,adopt Taiwan’s TECO motor;

2. Electrical cabinet surface electrostatic spray paint, wear beautiful.

3.   Electrical components Schneider and DELIXI brand.

 
14.

Lum-D

 Automatic         Gluing making system

 

 1.Concentrate glue making and separate glue supply;

；

 

  1. This line adopts frequency conversion control for speed regulating motor
  2. This configuration picture is for reference only, subject to the actual type, the equipment is subject to change without prior
  3. This price includes tax and
  4. If you need to add or subtract configuration, please negotiate the price separately. The buyer shall provide accommodation for installers

 

Note:

  1. In addition to the servo motor of computerized spiral knife NC cutter machine, each transmission part of the production line is frequency conversion speed regulation, partial transmission, the whole line
  2. All rollers were tested for static balance, accuracy grade
  3. Pneumatic system includes pneumatic control box, cylinder, pipe joint, excluding air compressor, gas storage tank and
  4. Glue control device does not contain glue pump does not contain
  5. Electric control system includes electric control cabinet, operating table, without wires and cable

 

Latest Products
Kappa board production machine

  The cardboard composite production line is suitable for 2-4 layers

Hardboard production line

  The cardboard composite production line is suitable for 2-4 layers

Thermo bond machine

  PART A: SPECIFICATIONS                                                                                  Finished product: thermo-bonded nonwoven fabric Product

DOUBLE DOT COATING MACHINE

  RX2600-DOUBLE DOT COATING MACHINE (Tuff Register) Usage: This machine is